Inconel 718 holds its yield strength close to 700°C and resists oxidation, chloride pitting, and stress corrosion cracking in sour and marine service. That performance comes from a precipitation-hardening reaction built around niobium, titanium, and aluminium additions to a nickel-chromium matrix. Fabricators buy the alloy in flat-rolled form whenever a part needs thin section plus high strength, and two product forms dominate that space. Inconel 718 foil sits at the thinnest end of the gauge range. Strip covers heavier sections and wider widths, usually in coil. Gauge decides how the material forms, how a weld penetrates, and how the component responds to ageing, so thickness selection belongs at the design stage.
What Is Inconel 718 Foil?
Foil describes Inconel 718 rolled down to very light gauges, where thickness control and flatness matter more than bulk strength. Shim stacks, thin liners, diaphragm layers, sealing elements and honeycomb core material all draw on this form. Rolling to such light sections work-hardens the alloy heavily, so suppliers deliver foil in a solution-annealed or cold-worked condition depending on the forming route ahead of it. Surface finish carries real weight here. A bright annealed or lightly polished surface helps when the foil goes into a brazed or diffusion-bonded joint, because oxide films at that thickness interfere with wetting. Handling also changes character below roughly 0.15 mm. Creasing, edge tearing, and interleaving damage become genuine scrap risks, which is why foil ships in protected rolls or flat-packed cut sheets.
What Is Inconel 718 Strip?
Strip arrives as flat-rolled material in narrow or wide widths, supplied either as coil for continuous feeding or as cut lengths for batch work. Stamping presses, roll forming lines, and slitting operations all run on it. Consistent thickness across the width and along the coil length keeps die clearance stable, which is the main reason press shops specify strip. Edge condition changes the result too. Slit edges suit progressive die work, while deburred or round edges reduce crack initiation during tight-radius bending. Temper matters just as much, since solution-annealed strip forms readily and age-hardened strip does not. One point deserves emphasis: calling a product strip says nothing about its mechanical properties. Those come from the governing specification, the heat treatment condition, and the test certificate.
Key Differences Between Inconel 718 Foil and Strip
Thickness separates the two forms first, and every other difference follows from it. Foil demands careful handling, interleaving and flatness control. Strip tolerates mechanical feeding, coil tension and automated decoiling. Width ranges differ as well, with strip supplied in slit widths that match die layouts. Applications split along the same line, foil going into shims and thin liners while strip feeds stamped and formed components. Product-form definitions vary between governing specifications, so confirm the required thickness band with your supplier before releasing an order.
Table 1: Inconel 718 Foil vs Strip
| Comparison factor | Inconel 718 foil | Inconel 718 strip |
| Thickness | Generally thinner gauge | Often supplied in greater thicknesses |
| Supply form | Rolls or cut sheets | Coils or cut lengths |
| Handling | Requires careful handling due to thinness | Depends on thickness, width and temper |
| Typical uses | Precision shims, thin liners and specialised components | Stamped parts, formed components and fabricated strips |
| Selection factors | Gauge, flatness, finish and condition | Thickness, width, edge condition and condition |
Use the applicable product specification to confirm exact foil and strip classifications.
Thickness, Dimensions and Material Condition
- Define required thickness with its tolerance band, because gauge variation across width affects die clearance and weld penetration consistency.
- State width, cut length or coil inside diameter early, since slitting capacity limits what any supplier can deliver quickly.
- Specify the condition: annealed, solution-treated or age-hardened, as the applicable material specification and your fabrication sequence allow.
- Confirm surface finish and edge requirements, covering bright annealed, polished, slit, deburred, or round edge preparation.
- List downstream operations such as forming, stamping, welding or brazing so the mill supplies a workable temper.
Gauge and heat-treatment condition together govern springback, drawability and weld behaviour. A component that forms cleanly in annealed strip may crack in the aged condition, which makes the design requirement the deciding factor.
Industrial Applications of Inconel 718 Foil and Strip
- Aerospace: Thin liners, shims, and selected fabricated components where thermal cycling and fatigue loading govern the design.
- Power generation: Parts exposed to demanding thermal and mechanical conditions inside turbine and exhaust assemblies.
- Chemical processing: Selected equipment components requiring corrosion resistance suited to the specific media and operating temperature.
- Precision manufacturing: Thin formed, stamped, or etched components where dimensional tolerance drives the material choice.
Service conditions, engineering specifications and the qualified heat-treatment condition determine whether a given gauge and temper fit the application.
How to Choose the Right Inconel 718 Product Form
- Choose Inconel 718 foil when the design calls for a very thin material gauge.
- Consider strip when the component needs a specified width, coil supply or repeated forming and stamping operations.
- Confirm thickness, width, dimensional tolerances, and the supplied material condition against the component drawing.
- Check the governing specification and request material test documentation covering chemistry, mechanical properties and heat treatment.
- Verify availability and dimensional range against the supplier’s current stock before committing to a production schedule.
Conclusion
Foil and strip answer different fabrication problems. Foil solves the thin-gauge, high-precision case where shims, liners, and sealing layers demand flatness and controlled surface condition, while strip serves width-driven, volume forming work on presses and roll lines. Thickness, width, material condition and the intended fabrication route guide the decision between them. Confirm the applicable specification and every dimensional requirement before releasing an order, particularly for precision or safety-related components.
Contact AB Steel to confirm gauge and width availability for your Inconel 718 requirement.